How to install a faucet into an acrylic bathtub

Although installing a faucet in an acrylic bathtub may seem difficult, it’s a manageable project for any do-it-yourselfer with the right tools and a little perseverance. This guide will walk you through every step of the process, whether you’re remodeling your bathroom or just changing out an outdated faucet. Together, we can successfully complete your bathroom renovation.

Ensure you have all the required instruments and supplies before you begin. A new faucet, silicone sealant, plumber’s tape, a wrench, a drill, and a hole saw are required. To prevent any unintentional spills, make sure you turn off the water supply. The installation will proceed much more quickly and easily if the workspace is tidy and the tools are arranged.

Mark the location of the faucet installation to start. Make sure it’s centered and at a comfortable height by taking precise measurements. Make sure you precisely follow the marked lines as you use the hole saw to cut through the acrylic. Take your time to avoid making any mistakes because this step calls for steady hands and patience.

It’s time to install the faucet after the hole has been cut. For instructions on how to attach the faucet to the tub, refer to the manufacturer. This usually entails using a wrench to tighten the nuts and washers that secure the faucet. To make sure there is a tight seal and stop leaks, place plumber’s tape on the threads.

Put a bead of silicone sealant around the base of the faucet after it has been secured to form a waterproof seal. By doing this, you can stop water from leaking under the faucet and harming your bathtub. Before testing the faucet, let the sealant dry completely.

Lastly, reactivate the water supply and inspect it for leaks. For a few minutes, run the water to make sure everything is operating as it should. Tighten the connections and use more plumber’s tape if needed if any leaks are found. Once everything is set up, your new faucet should be operational and ready to enhance the appearance and usability of your acrylic bathtub.

Step Description
1. Gather Tools Collect wrench, screwdriver, plumber"s tape, and the faucet kit.
2. Turn Off Water Shut off the water supply to the bathtub.
3. Mark Holes Mark the positions for the faucet holes on the tub.
4. Drill Holes Carefully drill holes where you marked them.
5. Install Faucet Place the faucet in the holes and secure it with provided nuts.
6. Connect Water Lines Attach the hot and cold water lines to the faucet.
7. Check for Leaks Turn the water back on and check for leaks.

Features of insertion of mixers

Traditional bathroom faucets, which are typically mounted on the wall at the end of the laundry machine, are progressively going extinct. Decorative shut-off valve models that are mounted directly on the ship, like the one in the top photo, are becoming more and more common these days. Thus, the query: "How do I drill a bathtub made of acrylic?"

Types of designs and configurations

In principle, almost all built-in faucets that are mounted on board acrylic bathtubs are a set of autonomous units that have a separate mounting system. The spout, shower head, hot and cold taps are mounted separately from each other, and for each unit you need to drill a seat. However, two valves with faucets can be mounted separately from each other, but it can also be a single lever switch with a cartridge for mixing and separating flows. The most important thing is that you understand that the installation of a mixer on an acrylic bathtub is carried out only in accordance with the installation diagram, which will definitely be in the box with all the components.

You can, of course, ignore such faucets because of their high cost, but we must not forget that you always have to pay more for quality and the highest class of aesthetics. For example, most manufacturers provide a guarantee for their products for up to 5 years, which cannot be said about the standard versions of such devices. And the point here is not only in the quality of the metal, but in the design features of shut-off valves of this type, where each node functions autonomously without affecting the others. In addition, mortise faucets can be installed after tiling the bathroom, which is also not without convenience, since it may be necessary to replace the bathtub (washing bowl).

How to make a hole

As an alternative, you can use a diamond-coated hole saw made for granite, marble, and glass to drill the acrylic bathtub’s side flap. However, composite materials (composites), which are actually a part of acrylic, can be drilled for such crowns. A milling cutter that resembles two drops of water is comparable to a successful one, except that drilling is not harmed in this case. In other words, when in rotation mode, they function just like a diamond crown.

On the Internet, it is often possible to find tips that are recommended for drilling acrylic baths to use a drill/Freze Forester (call it as you want). Yes, indeed, this is a very convenient cutting tool, which is easy to drill the side lapel of the bathroom for installing a crazy mixer. As a rule, for the installation of nodes, landing holes with a diameter of 35 mm corresponding to the diameter of the installed part are needed. This means that you will have to purchase a rather expensive drill of the desired size, which may never be needed in the household. In addition, such cutters are designed for drilling recesses in furniture for the installation of awnings and door closers, therefore, there is a passage depth limiter. Be that as it may, if you have such a cutter at home, you can easily make through mounting holes in acrylic.

It is much more profitable to purchase a conical stepped drill for installing a mixer in an acrylic bathtub, which is never superfluous in the household. The uniqueness of such a cutting tool is that it can make holes with a diameter of 6 to 40 mm (there are models from 4 to 80 mm) – each successive step has its own diameter (this is clearly visible in the photo above). The drill is intended not only for plastic and wood, but also for sheet steel up to 5 mm thick. As you probably already understood, with such a tool you can drill mounting holes in the bathroom, and then use it in the household for a long time. The quality of a drill can be determined by its color: golden-colored drills perform best, although they are all made of tool steel (high-alloy) HSS, but if there are cobalt additives (HSS – Co), then this is the best option.

Note: The faucet can also be mounted on the flap of a steel or cast iron bathtub by using a tapered step drill.

Tools required for installing a mortise mixer

For installing a faucet on an acrylic bathtub, the following equipment is required:

  • an electric drill, but for acrylic a screwdriver will suffice;
  • diamond core bit, Forstner cutter or tapered step drill;
  • a pair of gas or adjustable wrenches;
  • a metric tape measure, or even better, a caliper;
  • marker or pencil.

Mixer installation

You can start the installation process now that you know what equipment is required to install a faucet on the side of an acrylic bathtub. First, you must mark the centers of the intended mounting holes according to the documentation that comes with the mixer in the box. The number of nodes in the shut-off valve mechanism will indicate whether you require one, three, or four of them, depending on the type of crane you have. This information is also included in the passport.

Don’t rush into drilling holes after marking in accordance with the part diameters; instead, drill the centers first using a metal drill with a diameter of 3–4 mm to ensure maximum accuracy. Then there won’t be any side deviation from the crown, Forstner cutter, or step drill (decentering of the holes won’t occur). Apply the necessary amount of landing cuts.

Follow the manufacturer’s instructions, which are included in the documents, to assemble the faucet on the acrylic bathtub’s flap. However, do not connect it to the cold and hot water fittings. Install the overflow and siphon.

Attach the mixer pipes to the cold and cold water, and the siphon to the sewer fitting. Verify the drainage quality and the operation of each and every faucet.

Although it may seem difficult, installing a faucet in an acrylic bathtub is a task you can do on your own if you have the necessary equipment and a little perseverance. You can guarantee a long-lasting, secure, and polished installation by following these guidelines.

First, assemble all required equipment and supplies, such as the drill, faucet, and plumbing supplies. To prevent errors, measure and mark the faucet’s location precisely. To avoid damage or cracks when drilling into acrylic, use a steady hand and the appropriate drill bit.

After drilling the holes, firmly fasten the faucet and make sure all of the connections are tight to avoid leaks. For precise instructions on sealing and fastening the faucet, refer to the manufacturer’s instructions. Making sure that every connection is double-checked is essential to keeping a tight seal.

Test the faucet thoroughly by running water and looking for leaks after installation. Any concerns should be resolved right away to prevent more issues. Now that everything is set up and functioning properly, you can relax and enjoy your upgraded bathtub, knowing that your do-it-yourself project was a success.

The ease of installation of a faucet into an acrylic bathtub can improve the appearance and usability of your bathroom. Begin by choosing the appropriate faucet and gathering necessary equipment, like a wrench, plumber’s tape, and a drill. Make sure the faucet hole locations correspond with the bathtub’s design by carefully measuring and marking the locations. As directed by the manufacturer, drill the holes and then firmly fasten the faucet. Lastly, make sure everything is correctly sealed, connect the plumbing, and inspect for leaks. You can successfully install a faucet that gives your bathtub more style and convenience if you are patient and pay close attention to details.

Video on the topic

Installing a built-in faucet on the side of the bathtub / Connecting an acrylic bathtub / Draining the overflow onto the bathtub

Installing a faucet on the side of an acrylic bathtub

Installation of a mortise mixer on an acrylic bathtub

We drill acrylic. Crane installation on acrylic bathtub

Installing the mixer on board the acrylic bathtub, as well as how to fix the radiators

Ledeme l1153 bathtub mixer on board

Slothing the mixer into the board of the bath (how to cut the mixer into the bathroom)

Installation of the mixer on board the acrylic bathtub.

What factor is most important for you when choosing materials for building a house??
Share to friends
Konstantin Zhukov

Gardener, landscape designer. I will help you create a beautiful and functional landscape design for your site.

Rate author
StroyArsenal62.com
Add a comment