It shouldn’t be too difficult to install a mixer tap in the bathroom because it only requires a few simple supplies and tools. Let’s look at detailed instructions for installing a mixer tap in connections that have already been made, such as wall water outlets. However, in the event that no connections are present, they can be easily made, for instance, by utilizing a polypropylene strip with two water outlets underneath the mixer.
Usually, the hot and cold water supply pipes for the bathtub mixer are concealed within the walls, arranging the system so that only two 3/4-inch threaded connections are visible in the tile, particularly beneath the mixer. As it is improper to frog the compounds on the soldering and it is not advised to hide behind the finish, such water outlets should be connected with a metal-plastic connector.
- How to bring polypropylene pipes to connect the mixer
- The first stage – screw in the eccentrics
- Trying on the mixer, installing reflectors
- Assembling and installing a shower head
- Video on the topic
- Changing the faucet in the bathroom. Replacing the faucet yourself.
- Installing a faucet in the bathroom
- Secrets of installing plumbing fixtures in the bathroom Do-it-yourself faucet installation
- All the “tricks” for replacing a bathroom faucet
- HOW TO INSTALL A MIXER TAP IN THE BATHROOM WITH YOUR OWN HANDS ✔ Watch and learn!
- Replacing and installing a bathroom faucet step by step | With your own hands
- Installing a faucet in the bathroom. And what might happen.
How to bring polypropylene pipes to connect the mixer
A polypropylene adapter, which is a stationary bar with two water outlets, is required for the mixer. It can be fastened to the wall with dowels and is constructed like a bar with threaded connections. Installable over the finish if desired.
The only thing left to do is bring the soldering (connecting polypropylene pipes), for instance, in accordance with the photo’s scheme or the traditional version, which consists of two pipes supplying below.
However, the bathtub will rest against these pipes and not fit against the wall if the mixer is above it and these pipes are on top of the finish. On the other hand, the bathtub is typically mounted up against the wall.
The pipes are positioned sideways over the side as a result. Generally speaking, the mixer should form two water outlets as a result of these efforts.
The first stage – screw in the eccentrics
Eccentrics, or adapter couplings with offset hole centers, are required for the mixer. You can choose the basic distance to connect the mixer when they rotate, which happens when they are screwed into water sockets.
We wind the plumbing thread in a single layer along the thread, lubricate (sunflower oil works well), and use a wrench to screw it in with medium force (don’t use too much force; you have to rewind!). It is advised to use FUM tape only on plastic threads rather than metal ones. Additionally, the fum tape frequently leaks when an eccentric turns the connection back and forth.
The eccentrics then need to have reflectors installed on them. These are two sizable caps that cover up the entire mount underneath. However, there’s no need to install them right away.
Trying on the mixer, installing reflectors
Testing the mixer assembly on the eccentrics is essential. It has union rotating nuts attached to it. When tightening the connection with a wrench, rubber gaskets that offer an end-to-end seal should be placed beneath the nuts. It’s best to choose silicone washers by size at a plumbing supply store right away because it’s been observed that gray manufacturers may use whole seals composed of unidentified materials.
To align the eccentrics with the mixer union nuts, rotation is applied if needed. You must make an effort to ensure that the device is not skewed, particularly if there are adjacent bright horizontal tile joints.
Verify that there are no leaks beneath the eccentrics. To accomplish this, put the mixer on, loosen the nuts a little, turn on the water, and check and feel for moisture in the connection.
Since we performed the task correctly and everything is in working order, we take out the mixer, install the device with the nuts tightened, and then screw the reflectors onto the eccentrics until they stop. You can now turn on the water and test the device’s functionality.
Assembling and installing a shower head
A flexible tube, a shower head, and fasteners to secure the shower head on the wall—for instance, high above the bathtub—should all be included in the kit.
The traditional way to install a rain shower is on the same center line as the faucet, right above it on the wall.
Typically, the hose has union nuts around its edges. End gaskets seal the hose’s connections to the watering can and mixer outlet; these gaskets should probably be changed as well. We tighten the nuts on the mixer and watering can and make sure the rain is working properly.
The mount on the wall needs to be installed next; typically, this requires two plastic plugs for self-tapping screws. In order to stand comfortably beneath the shower and prevent the hose loop from touching the bath’s side, we fasten the mount to the wall at the designated height, mark.
If you follow the proper procedures, installing a mixer tap in your bathroom can be a simple do-it-yourself project. This tutorial will lead you through every step of the process, from assembling the required equipment and supplies to guaranteeing a safe and leak-free installation. You can save money by hiring a professional and quickly get your new mixer up and running with simple instructions and a little perseverance.
We make marks at the attachment points by removing the enamel from the tile. We use a diamond drill (a non-impact drill) to go through the tiles, and then we drill into the concrete using an impact drill. We use self-tapping screws to secure the mount beneath the watering can after hammering the plugs into the holes. That’s all; the shower head is at the top and the bathroom faucet is in place.
