How to make a garage roof from corrugated sheets beautifully and without mistakes?

Using corrugated sheets for garage roof construction offers both practicality and durability. They not only provide your garage a sleek and contemporary appearance, but they are also resilient against weather conditions like rain and snow. To ensure both functionality and aesthetic appeal, installing a corrugated sheet roof requires careful planning and execution.

Accurate measurement and planning are essential first steps in building a stunning corrugated sheet garage roof. To begin, precisely measure the size of the roof area of your garage. Consider any angles or slopes that could have an impact on the arrangement of the sheets. Making a plan in advance guarantees that you order the appropriate number of sheets and accessories, such as screws and ridge caps.

Next, think about your garage roof’s pitch or slope. The best results are achieved with corrugated sheets on roofs that have a slight slope, usually 5 degrees or more. This slope facilitates effective water drainage and keeps water from collecting, which over time may cause leaks. Make sure the structure of your roof can sustain this slope and offer a firm foundation for safely installing the sheets.

Thoroughly prepare the roof surface before installation. Make sure the surface is even and smooth, and clean up any debris. To improve thermal efficiency and avoid condensation inside the garage, you might need to install insulation or a vapor barrier underneath the corrugated sheets, depending on your climate and local building codes.

Properties and characteristics of the material

Using specialized cold rolling mills, flat galvanized steel sheet is transformed into profiled roofing decking, which gives the material a distinctive wavy relief.

Like a pie, the profiled sheet is made up of multiple layers:

• the steel sheet itself, which can have different thicknesses and acts as a base;
• galvanized coating applied to this very base on both sides;
• the so-called “soil”, which, along with passivation oxides, prevents chemical processes of interaction between materials of different compositions (oxidation, rust, decomposition, etc.d.);
• depending on its purpose, the profiled sheet may have in its structure various polymer materials, composite components, additional additives, additives.

Such a "layer cake" thus gains distinctive characteristics and consumer attributes. And when it comes to the garage roof in particular, corrugated sheeting is probably the best choice.

Key characteristics of a profiled sheet

Price per linear meter	280 – 800 rubles depending on the composition
Life time	Minimum 10 years
Features of operation	No – this is a universal practical material
Installation difficulty level	Easy
Requirement for sophisticated equipment during installation	Absent

Pros and cons of metal profiles

Profiled steel sheet is best suited for roofing outbuildings and garages because of its characteristics. This is because of the benefits that this substance offers:

• a fairly high degree of strength and durability (at least 10 years, in fact much more);
• immunity to oxidation (the appearance of rust, for example), the appearance of fungus, mold and pests;
• resistance to chemical reagents and other aggressive environments;
• high fire safety parameters;
• lightness, ductility, flexibility, which allows the use of profiled sheets without the need for special equipment or heavy equipment;
• unpretentiousness in operation and maintenance.

In addition, it is simple to replace any damaged areas of the profile flooring. Furthermore, the roofing sheet may seem fairly attractive, depending on the components used in the material and the manufacturing process.

The majority of galvanized profiled metal sheet has no significant drawbacks. One of the drawbacks of using it as a roofing material is that the least expensive variety has an ugly appearance.

Low noise insulation parameters are another example of conditional disadvantages. Raindrops, falling branches, and other sounds will be audible under a corrugated roof. That being said, this is not as important in the case of a garage. Furthermore, this issue can be resolved with the aid of reasonably priced soundproofing materials.

It is not always appropriate to use corrugated sheet metal for a garage’s roof in certain weather situations. The roof may simply not withstand a large mass of snow or water collected after two or three heavy rains because of its light weight and flexibility, which are the roofing material’s absolute advantages.

Which corrugated sheet is better to choose for the roof??

You must comprehend the labeling and technical features of a material in order to select one of high quality. Now let’s examine the metal markings to accomplish this.

The designation "N" indicates that a roofing sheet is load-bearing. Rolling metal products with the designation "NS"—load-bearing wall or universal—may be used. The technical characteristics of corrugated sheets with the letter "C" – wall sheets do not meet the requirements for roofing, so they cannot be used to cover the roof.

The standard sizes, thickness, and wave height of the sheet are indicated by the numbers in the documentation for rolled metal products. Furthermore, the coating type and color can be shown on the marking. It is crucial to comprehend the meaning of the information provided on the label.

• Sheet thickness. Selected depending on future loads, angle of inclination and operating conditions of the roof. The lower the slope and the greater the load, the thicker the rolled metal should be. The thickness of the steel base must be at least 0.5 mm – this is an acceptable minimum provided that continuous sheathing is used. Experts recommend taking material from 0.8 to 1.5 mm.
• Wave height. The larger the wave, the higher the rigidity and strength of the material. For roofing, you cannot use sheets with a wave height of less than 20 mm. Moreover, the smaller the slope angle, the higher this indicator should be.
• Sheet width – total and working. This indicator is important to take into account when calculating the amount of building material. Since the sheets need to be laid with an overlap of 1 or 2 waves, the working width is taken into account. And the total can only affect the width of the body of the delivery vehicle.
• Coverage type. The cheapest option is galvanizing, but it quickly loses its appearance and becomes unusable. However, for household buildings and garages this choice is quite justified. Expensive polyester coating has a wide variety of shades and perfectly protects building materials from corrosion. But the small thickness of the protective layer is easily damaged. The best option in terms of price/quality ratio would be a coating made of pural, which is resistant to aggressive influences and has a long service life.
• Colors. Does not affect the operation of the roof in any way. Depends only on the preferences of the owner.

The cost of a linear meter of corrugated galvanized sheet ranges from 280 to 800 rubles, depending on its features, component composition, and fundamental attributes. A profiled sheet’s cost increases with the complexity of its constituent parts, but it also improves with increased strength and durability.

Leading manufacturers

On the Russian market for building supplies, producers of premium profiled galvanized steel sheets are in plentiful supply. Among them, the following are the most well-liked:

• "Metal Profile";
• "Pokroff";
• UZKM;
• "Neva Steel";
• GRAND LINE.

Naturally, this is by no means an all-inclusive list. Numerous local producers are making affordable, high-quality certified goods.

In our tutorial, "How to Make a Garage Roof from Corrugated Sheets Beautifully and Without Mistakes," we go over doable methods for utilizing corrugated sheets to create a reliable and attractive garage roof. From crucial planning and material selection to accurate installation methods, our goal is to provide readers with the knowledge they need to approach this project with confidence. Whether you’re building a new roof or renovating an old one, these easily accessible guidelines guarantee a successful roofing project that improves curb appeal and functionality.

How to make a roof with your own hands?

You must get ready before attaching the corrugated sheets to the roof. It won’t be unnecessary to create a skillful drawing at first. This will not only help you figure out how much material you’ll need in the end and how much it will cost, but it will also help you avoid making mistakes when doing roofing work.

You must divide the slope’s width by the sheet’s working width in order to determine how many sheets there are in a row on a given slope. and add up the outcome.

The computation stops here if one sheet’s length is sufficient to cover the entire slope, including overhangs. If not, the number of horizontal rows must be determined. It’s critical to keep in mind the degree of horizontal inter-row overlap in this situation. It is dependent upon the slope’s angle of inclination.

Additionally, you must properly arrange the under-roof space before closing the roof. It is advisable to set up a waterproofing layer made of suitable materials to improve the room’s moisture insulation qualities and to lengthen the lifespan of the galvanized profiled sheet roof covering.

The waterproofing needs to be put on after the frame is assembled. Using a construction stapler, it is fastened to the rafters. Rolling the material across the whole width of the slope, it should be mounted from the bottom edge of the rafters. The subsequent row is joined to the underlying one by overlap. When the temperature drops, the waterproofing is installed with a small sag to prevent rupture.

A counter-lattice is used to secure the waterproofing material. Next, sheathing boards are nailed in horizontal rows to the counter-lattice. They will have the corrugated sheeting fastened to them.

To improve drainage and keep a lot of moisture out of the building’s walls, the edges of both flat and pitched roofs should protrude past the eaves by at least 50 mm.

See this video to learn how to construct a pitched garage roof on your own using corrugated sheets:

How to cover it yourself?

The type of roof determines the order in which sheets are laid:

• The 2-slope begins to be closed from any end from right to left or from left to right;
• The 4-slope is closed from the longitudinal central axis of each hip.

Using a cord that is stretched along the cornice, align the corrugated sheets horizontally.

Simple installation techniques:

1. Three-block — installation of sheets without capillary grooves. Lay 2 sheets of the first row, align them along the cornice and temporarily fix them. Then comes the 1st sheet of the second row, aligned, and then the entire block is attached. Then the installation proceeds in a checkerboard pattern, with alternating sheets in each first and second row.
2. Four-block — installation with capillary grooves to remove moisture at joints. The following are mounted in turn: 1st sheet of the 1st row, 1st sheet of the 2nd row, 2nd sheet of the 1st row and 2nd sheet of the 2nd row. Each sheet is temporarily attached to the sheathing at a central point, and after the entire block is leveled, it is finally fixed. Next, the next block is mounted according to the same scheme.

The easiest is the row method, where the profiled sheets are fully laid in the first bottom row, then the second, and so on.

The next sheet can be laid on top of the preceding sheet or beneath it with a wave overlap. Any kind of overlap should only have joints pointing in one direction.

It is preferable to use a hacksaw or metal scissors to trim sheets if necessary. Corrosion spots appear and the protective polymer layer is damaged when an angle grinder (grinder) with an abrasive wheel is used.

Fixation and fastening

It takes galvanized roofing screws to secure the corrugated sheeting. They have a metal-colored head paint, a neoprene rubber gasket, and a drill bit attached.

The thickness of the sheathing is taken into consideration when choosing the screw length. To prevent harm to the waterproofing, the fasteners must not pass through the board. Six to eight fasteners are typically sufficient for one square meter of coverage.

The following guidelines must be adhered to when using fasteners:

• The corrugated sheets are fixed to each other in the upper wave every 50 cm;
• fastening to the sheathing is carried out in the lower wave in vertical increments – in each row of the sheathing, horizontally – after 1 wave;
• corrugated sheets are attached to the 1st bottom row of the sheathing in each wave;
• the fastener must be screwed along the cord to create a straight line of fastening;
• you need to adjust the force when screwing in the screws – you can’t overpress them by pinching the gasket too much, but under-tightening is also bad.

Depending on the type of structure, installing ridge and wind strips, valleys, snow retainers, and other finishing elements may be required after the roof is covered in corrugated sheets. The same roofing screws are used to secure them to the metal profile and frame components.

After weighing the pros and cons of each option, it is clear that a garage roof composed of galvanized profiled steel sheet is the most sensible, affordable, and useful choice.

Useful video

Watch this video to learn the installation guidelines for corrugated roofing:

Topic

How to make a garage roof from corrugated sheets beautifully and without mistakes?

Main Steps

1. Measure and prepare the roof frame according to the dimensions of the corrugated sheets. 2. Ensure proper alignment and leveling of the frame to prevent uneven roofing. 3. Lay down insulation if needed for climate control inside the garage. 4. Start from one end of the roof and secure the first corrugated sheet, overlapping correctly. 5. Continue laying sheets, ensuring each overlaps and aligns properly until the roof is fully covered. 6. Secure sheets with appropriate fasteners to prevent lifting or water leakage. 7. Trim excess material carefully for a neat finish.

If done correctly, building a garage roof out of corrugated sheets can be both useful and aesthetically pleasing. A project’s success is mostly dependent on careful planning and close attention to detail. Make sure you have the appropriate supplies and equipment before you begin. To calculate how many corrugated sheets you’ll need for your garage, take precise measurements and account for any extra materials you might need, such as sealants or insulation.

Make sure you closely adhere to the manufacturer’s instructions when installing the sheets. Starting from one end of the roof, proceed across it, making sure that every sheet is securely fastened to avoid leaks and guarantee stability. To guarantee that the sheets are firmly fastened to the roof structure, use the proper fasteners and installation methods. To keep the waterproofing and durability, pay attention to the joints and overlaps.

Take into account your garage roof’s aesthetic features as well. Select corrugated sheet colors and profiles that go well with the exterior of your house. This improves your property’s curb appeal overall in addition to its aesthetic appeal. Sheets that are properly trimmed and aligned can offer dependable weather protection and a polished appearance for your garage.

Last but not least, maintaining your corrugated roof on a regular basis is essential. Check it from time to time for wear and damage indicators, like rust or loose fasteners, and take quick action to fix any problems you find. Your home’s value will increase for years to come with a long-lasting, visually appealing garage roof if you take the time to install and maintain it properly.

Video on the topic

DIY garage roof

Garage roof. Corrugated garage roof.

DO-It-yourself garage roof made of corrugated sheets

option for attaching corrugated sheeting to a flat roof to prevent water from entering.

Roof for a garage made of corrugated sheets. Correct roof!

Roof of a warm garage made of corrugated sheets