How to make a hook for knitting reinforcement with your own hands?

In many building projects, knitting reinforcement is an essential step in ensuring that the structure has the strength and stability that it needs. Although there are many tools available for this kind of work, creating your own hook for knitting reinforcement can be an enjoyable and affordable project.

This post will walk you through the process of making a straightforward but powerful hook out of supplies you probably already own. This will not only save you money, but it will also provide you with a useful tool that is customized to meet your individual needs.

The ability to create a hook for knitting reinforcement is useful regardless of your level of experience as a builder or level of do-it-yourself enthusiasm. Let’s examine the procedures and advice for creating your

Necessary materials and tools

To create your own knitting reinforcement hook, you will require the following supplies and equipment:

• electrode with a diameter of 4 mm or a steel rod, 4 mm thick;
• a piece of hose or a ready-made handle from another tool;
• a sharpening machine;
• a vice.

A mechanic does not require a drawing to be prepared because.To. The hand hook’s design is so straightforward that any worker can construct one for themselves.

Instructions for making a hook

Builders’ needs are frequently not entirely met by factory products, particularly when knitting the foundation’s frame requires a significant amount of labor. Let’s examine how to create a hook using your hands for tying reinforcement.

Most frequently, workers point out that the tip was bent incorrectly or that the rod is too short, making it difficult to tie knots in awkward locations. In these situations, you have to use leftover materials to make a crochet hook right there on the construction site.

From reinforcement

Making a homemade hook will take no more than two hours. The tool is made by the fitter to the exact measurements needed to fit his hand. In order to create a hook out of reinforcement, you must first:

• a piece of corrugated reinforcement 350-500 mm long. The thickness of the rod is no more than 10 mm;
• blank for handle made of wood or plastic;
• two washers with an inner diameter equal to the thickness of the rod;
• two nuts or two bearings;
• Passatigi;
• axe;
• electric drill with a drill on wood 10 mm;
• angle grinding machine with a disk for cutting metal;
• sandpaper.

The steps involved in creating a hook for hand-knitted reinforcement are as follows:

• To give the future product a smooth surface, iron ribs are cut off with a rod with an angle -grinding machine. This item could be skipped if you immediately take a smooth reinforcing rod, but corrugated rods have a higher strength and are better suited for making a home -made tool.

• The wooden blank is drilled in the center, adjusting the hole under the diameter of the rod. You need to make a hole exactly in the center of the handle. After fitting the handle, it is polished with sandpaper.

• A locking nut is welded to one end of the rod, not allowing the handle to fly. A bearing can also be used for this purpose. A washer, a wooden handle, a washer and a nut are sequentially placed on the rod. In order for the handle to rotate well when knitting wire, there should be a small distance between the washers. Therefore, when welding the second nut, you need to place paper folded several times between the handle and the washer, which can then be easily removed.
• The second end of the rod is sharpened using an angle grinder and a metal disc.
• Stepping back 15-20 mm from the handle, the rod is bent at an angle of 140 degrees, as shown in the figure. Having stepped back another 20 mm from the bend, the rod is bent again at an angle of 100 degrees. When working, you need to ensure that all bends do not extend beyond the same plane.

• To prevent the handle from drying out and cracking, it is painted with impregnation twice. After the impregnation has dried, varnish is applied.

Once the task is finished, a test knit is completed. If required, modify the rod’s bend angles and personalize the tool to fit your needs.

From the electrode

If you’re up for a little handiwork, you can use an electrode to create a hook for knitting reinforcement. You’ll require:

• angle grinder;
• pliers;
• electrode 4 mm.

Making a hook out of an electrode doesn’t take more than ten minutes, even for a novice craftsman. The following is the action algorithm:

• Flux is removed from the electrode;
• step back 20 mm from the end and bend the rod at an angle of 90 degrees;
• make an indent of 40 mm from the second end and also bend the rod at an angle of 90 degrees;
• moving from the second end further, at a distance of 120 mm from the first bend, the rod is again bent at an angle of 90 degrees;
• set aside another 50 mm and make another bend at the same angle;
• The end of the tool is sharpened with an angle grinder.

From a screwdriver

Making your own semi-automatic knitting machine with a screwdriver is even simpler. It is filled with a roofing nail, the head of which is removed with pliers, rather than ordinary bits. The tool is ready because the nail’s tip is bent at the appropriate angle.

How to use it correctly

There are hardly any variations in the construction of a reinforcement-framed structure used for pouring monolithic foundations, load-bearing walls, staircases, or floor slabs. Manual or semi-automatic hooks are used to tie wire between the joints of individual rods.

Use wire pieces that have been cut into 300–400 mm lengths to connect the components. The ideal segment length is determined experimentally while taking the thickness of the reinforcement into consideration in order to conserve material.

In addition, the wire needs to be annealed over a fire for 30 to 40 minutes if handling it reveals that it was bent too much. Once the wire has cooled, you can resume knitting.

Order of the tie-in reinforcement:

1. Wire is cut to specified size.
2. Each piece is folded in half and rotated around the central axis.
3. The finished piece is pushed under the junction of the rods from below.
4. The hook hooks the free end of the segment and the loop.
5. By turning the hook, the wire is pulled into a knot.
6. The knot is pulled until a strong connection is obtained.

Even inexperienced builders can successfully complete the knitting reinforcement process, but it would be wise to take a look at the picture or video below that shows this work in progress.

Creating your own knitting reinforcement hook is a simple and satisfying project. You can make a useful tool that will simplify and expedite your construction tasks with a few basic tools and materials. This do-it-yourself method not only saves costs but also enables customization to meet your unique requirements.

To begin with

Creating your own knitting reinforcement hook is an easy and affordable project that only requires basic tools and materials. Using supplies you probably already own at home, this tutorial will walk you through the process of making a reliable and effective hook. You can save money and have a dependable tool ready for your next building or repair project with just a few minutes of work.

Video on the topic

How to make a HOOK for KNITTING REINFORCEMENT

Hook for tying reinforcement/DIY/Hook for tying wire/Building a garage.

Do-it-yourself hook for tying reinforcement. How to make the perfect hook

Automatic hook for tying reinforcement Hitools

Knitting reinforcement with collets