The roof is already covered, but how to install gutters??

In order to safeguard your roof’s long-term integrity and shield your house from water damage, installing gutters is essential. Gutter systems are essential for controlling rainfall runoff because they divert it away from the foundation and stop erosion around your house, even though the roof itself offers protection.

It’s crucial to determine the ideal location for the gutters on your roof and its layout before you start installing them. Normally, gutters are mounted on the edge of the roof and slope downhill to the downspouts gradually. Water is guaranteed to flow effectively towards the specified drainage points at this angle.

Gutter materials can vary, but they are frequently made of copper, steel, vinyl, or aluminum. The benefits of each material vary depending on its cost, durability, and visual appeal. The right material to use will depend on a number of factors, including your climate, maintenance preferences, and budget.

Typically, the installation process entails precisely measuring and cutting the gutter sections to fit the roofline. In order to maintain the proper slope for water flow, it is imperative that the gutters are firmly attached using hangers or brackets made for the type of gutter you have chosen and that they are correctly aligned.

How to install a gutter after roof construction is completed: popular installation methods

Fastening to rafters

The brackets are typically intended to be fixed in this manner if the roof has already been installed, for example, and the drain needs to be gutted and replaced with a new system. First things first, the first row of roofing needs to be removed. You must undo the fasteners in this row of roofing before moving on to the next row in order to accomplish this. It is true that not all materials can be disassembled without compromising their integrity or causing deformation—particularly if the coating is nailed down—and that in some situations, this may not even be feasible.

Counsel Skilled roofers frequently use deceptive disclosure. There are special boards under the roof to prevent melting the coating. Next, start using pliers to twist the fasteners. Working with a soft roof that is installed on a continuous plywood crate is the simplest method.

-The brackets are started to be installed on the base as the lower edge of the roofing covering that runs along the eaves is carefully lifted.

-They are fastened with self-tapping screws by inserting the fasteners into the rafter legs through the plywood base.

• Next, the flexible tiles or roofing felt are returned to their place and fixed to the sheathing using bitumen mastic.

When dealing with slate, there is a considerable chance that issues will arise. However, you can use this material to accomplish something similar in this instance. Pre-planned and directly inserted into the waves of the slate sheet are wooden blocks that follow the wave’s profile. Gutter fasteners go through the block and the holder at the same time, right through the sheet material.

Rigid roof coverings need to be removed with caution. This advice is particularly crucial when dealing with outdated coating. After more than a year of use, roofing sheets are susceptible to damage that will require replacement.

An alternative method of fastening the hooks to the rafters is also an option. The side edge of the rafter beam is where the brackets are fastened. The holders have a horizontally curved mounting surface (this can be done separately). This kind of installation is only feasible if the rafters’ cross-section is sufficiently large—12 or 15 * 5 cm, for example. It is crucial to keep in mind that the roof covering should overlap the gutter by half or a third of its width when fastening the brackets. Then, you won’t need to be concerned that water will overflow the gutter’s edges due to heavy downpours.

Significant It goes without saying that preliminary fitting is necessary before installing brackets on the side edge of the rafter. It will become evident during the fitting procedure whether or not such an installation option is feasible.

The front board is a solid foundation

In passing

The board can be easily decorated to give the impression that it is a separate component of the roof’s exterior.

-If the wind board is sufficiently wide, long holders are used. The holder leg and hook of these brackets are both the same width, and they are composed of metal. The mounting platform, which is situated on the leg, has holes that are used to attach to the board.

-Short brackets can be mounted on walls and rafter ends in addition to wind boards, like long ones. Since the fasteners are positioned along the grain of the wood, the fastening’s dependability is called into question.

For metal roofs, short hooks made of the same material are chosen. You should also secure them to metal. PVC gutters are lightweight, making it simple to attach them to a wooden wind board.

Options for adjustable brackets that come with a unique gadget are especially noteworthy. It shifts one bracket component in relation to the other, determining the holder’s location’s slope, or the angle that creates the hook and base for the fasteners. You only need to tighten the adjustment screws to obtain the desired angle. These brackets are essentially essential when operating in challenging circumstances, such as when the wind board is slanted.

Prior to installing each individual holder, beat off a straight line on the wind board while keeping the slope toward the drain funnel between three and five mm/linear m. Mark the location of the first bracket’s fixation by stepping back from the edge of the wind board’s end section (the offset is roughly 50 to 100 mm). The installation locations of the holders are then marked along the entire length of the line, with increments of no more than 0.6 m (in certain cases, an even larger increment is acceptable; these must be noted in the instructions). Once the markings are finished, move on to mounting the brackets.

Because of the ample width of the roof overhang, installing gutters can also be done via another, highly practical method. A standard metal guide profile is mounted with unique short holders. The latter is then fastened, via the unique holes provided on it, to either the wind board or the house wall. The guide gets the necessary slope as soon as it is fastened. Therefore, there is no need to measure their height when installing the holders.

Next, the brackets are threaded from its side and positioned at the necessary pitch by moving them along the guide. Notably, since these holders "sit" quite firmly in the profile, they don’t need to be fixed. This is definitely an additional benefit of using such a fastening system.

"Crutches" as a basis

Attachment along the roof’s edgeWhen repairing a roof drainage system along its eaves, this approach makes sense. This choice works well with practically any kind of roofing material. Clamps, or as these particular clamps are called, are used to fasten the brackets. In the event that the system is fixed to a wave material, the holders are fastened to the wave’s upper or lower point. Rubber gaskets should be positioned beneath the metal clamps’ legs on both sides of the roofing sheet in this situation. By doing this, you can simultaneously address two issues: lessen the load and ease the compression on the sheet.

Additional brackets

There is one restriction on the use of short hooks when installing gutters using the aforementioned method. Furthermore, L-shaped metal brackets are needed. Their extended portion is fastened to the rafters’ side edges. A short PVC holder is fastened to the curved shelf that has a mounting platform on short sections. It is important to remember that in certain situations, this is your only chance to safely attach holders to a roof that has already been installed. For instance, if the roof extends 12 to 15 centimeters past the ends of the rafters on the eaves overhang.

Invisible brackets

In addition to the more common option of holding the gutter from below, the construction industry also offers brackets that hold the gutter from above. Once installed, they are invisible at all. 400–700 mm is the fixed distance between these holders. In the event that this requirement is broken, there’s a good chance that a heavy weight of ice or snow will cause the gutter to distort significantly.

It is necessary to bend brackets before using them to install to the sheathing or from above to the rafter. By doing this, the holder is given the desired shape and can then be perfectly adjusted to match the slope.

Tightening mount

Less people choose suspended mount than the alternatives mentioned above. Sometimes, though, this kind of design is the only option. The bends on this kind of bracket are unique. One of them is installed on the gutter’s front edge, and the other is attached to its back. There is an internal threaded sleeve attached to the holder. The gutter wall’s upper section and sleeve are where the fastening element is screwed into the wall or wind board.

It’s essential to install gutters after roofing in order to control rainwater runoff and shield your house from possible water damage. This article examines useful procedures and factors to take into account when installing gutters. It focuses on selecting the appropriate gutter materials, measuring and arranging the installation space, and making sure the slope is correct for effective drainage. Homeowners can protect their investment in their roof while strengthening their home’s resistance to water-related problems by taking the procedures outlined here.

In order to ensure proper drainage and shield your house from water damage, installing gutters is an essential step in finishing your roof project. For installation to be effective and durable, there are a few essential steps that must be followed.

Measure and plan the gutter system layout first, taking water flow and roof pitch into account. After that, put together all required parts and equipment, such as gutters, downspouts, brackets, and screws.

The gutters are supported by gutter hangers that are firmly installed at the proper intervals along the fascia board. To ensure effective water drainage, make sure they are level and slope in the direction of downspout outlets.

To stop leaks, use high-quality caulking or sealant to seal all joints and connections. Lastly, run water through the gutter system to test it and make any necessary adjustments for optimal performance.

These instructions will help you install gutters that will protect your home from water-related problems for many years to come. Your roof will function better and last longer with gutters installed.

Video on the topic

Three ways to install a gutter on an old house. My house

TOP 5 Gutter Installation Mistakes (Part 1) #shorts

GUTTER PROBLEMS AND SOLUTIONS / WHAT ARE GUTTER / WHAT IS GUTTER

Gutter for the roof with your own hands

How to assemble a plastic roof lining for a slate roof. How to install a drain, storm drain on slate?

A simple version of a roof drainage system made from sewer pipes

Lei lei don"t be sorry! DRAINAGE SYSTEM. Self-installation