Where should a double-circuit gas boiler be installed + its connection diagram

Selecting the ideal site for a double-circuit gas boiler installation is essential to the boiler’s safe and effective functioning in your house. Because these boilers supply hot water and maintain heating systems, it’s critical to locate them for optimal performance and accessibility.

First, think about placing the boiler close to an exterior wall in an area with good ventilation. This makes it easier for exhaust gases to be safely vented outside. Sufficient ventilation aids in preventing the accumulation of potentially dangerous gases such as carbon monoxide.

Placing the boiler adjacent to water pipes can also minimize heat loss and increase the effectiveness of hot water delivery. By reducing the distance hot water must travel, this configuration guarantees quicker access to hot water at all of your home’s taps.

Make sure the boiler is mounted on a stable, level surface when organizing the installation. This lessens vibrations while it is operating and supports its weight, extending its life and lowering noise levels in your home.

Installing a double-circuit gas boiler requires an understanding of the connection diagram. The connections between the boiler and the home hot water supply and heating system are shown in this diagram. It usually contains information about the locations of gas supply lines, electrical wiring, and water pipe connections.

Through meticulous installation site selection and adherence to the connection diagram, you can maximize the efficiency and safety of your double-circuit gas boiler, guaranteeing dependable hot water supply and effective heating for your home.

Where should a double-circuit boiler be installed??

When installing a double-circuit boiler, there are a few things to consider:

• Design features of the unit itself, outlined in the user manual.
• Current norms and rules for the installation of gas installations.
• Location of the common chimney, specific placement of the heating system and other features of the system.

A specific coaxial type chimney must be connected to the majority of double-circuit boilers. This unit is small and set up like a "pipe in pipe."

It is connected to the flue gas outlet from the inside, passes through the outer wall at the unit’s installation point, and is constructed from the outside in accordance with its unique operational requirements (special cap, mesh fencing, or other protection elements).

Such a chimney requires a sturdy, external wall to be installed. These units are usually placed in the kitchen.

An atmospheric boiler (one with an open combustion chamber) needs a minimum of 8 m2 of space, a window opening, and a separate room.

Due to their size and weight, floor-standing boilers typically select separate rooms on the lower levels of the house.

You should first carefully read the instructions, which provide instructions for their production as well as a clear description of the installation work conditions.

What requirements must be observed during installation??

You will need to combine two different sorts of requirements in order to complete installation work:

• Installation conditions set forth by manufacturers.
• Norms and rules for working with gas equipment.

The instructions always include a detailed description of the installation process. Any manufacturer has to specify the process, even in the absence of any special requirements.

Wall-mounted unit installation requires that you:

• The presence of a strong, ideally load-bearing wall, capable of supporting the weight of the boiler.
• Installation on thin or plasterboard partitions is prohibited.
• For gas boilers with an open burner, a separate room is required. If installation is in the kitchen, there must be a door and window opening.

Floor-standing boilers have specific needs.

• Installation is carried out on a layer of asbestos covered with a sheet of metal. This seems unnecessary, but most manufacturers, as well as gas service workers, are unanimous in this.
• A separate, ventilated room with access to any point of the boiler.
• The distance from the walls to the surfaces of the unit is at least 0.3 m (for some installations it is greater, please check the instructions).
• There should be no trash, flammable materials, or foreign objects in the room used as a boiler room. There should always be quick access to the window, access to the boiler from all sides should be free.

It is permitted to use a decorative box with opening flaps that is quickly detachable for wall-mounted installation in the kitchen.

The conditions for gas service are listed separately. The primary one forbids using gas equipment for unauthorized purposes. It states that installing, moving, and doing other tasks involving gas appliances is only permitted to gas specialists who are in possession of all necessary licenses and authorizations.

A fine is imposed for infractions. As per the regulations, the owner takes full responsibility after commissioning, signs the log, and goes through instructions. In actuality, things are a little unclear because these regulations were created with apartment building occupants in mind.

As a result, as long as there is no risk involved, they typically ignore some deviations from the norm.

Specifically, they typically reach a compromise: the owner can connect the boiler to the gas supply pipeline, but professionals handle connecting this pipeline to the main line.

The Russian Federation’s Art. 7.19 Code of Administrative Offenses states that connecting to gas networks without authorization is punishable (for individuals) by a fine of 3,000–4,000 rubles. Every action should be prearranged because any gas service inspector has the authority to declare the connection illegal.

Wall-mounted unit installation and connection diagram

Prior to anything else, make sure you have read the instructions thoroughly and have all the supplies and equipment ready. Only when there are no more unclear points can you begin working.

After all problems have been fixed, start the installation directly.

Let’s examine the process:

1. The boiler delivery set usually includes a template, according to which holes are made on the wall for anchors and a coaxial chimney. The bearing surface is marked on it.
2. Using a hammer drill, holes are made for anchors.
3. A mounting plate is attached to the anchor, on which the boiler is hung. This point cannot be neglected; the plate provides a technological and fire safety gap between the boiler and the wall. Its size must be at least 45 mm.
4. The boiler is attached to the plate using standard elements included in the delivery kit. All parts must be used and their quantity must not be reduced. There are often situations when the unit is installed in a corner, thereby violating the condition of having a 30-centimeter gap on all sides of the housing. In this case, there is no possibility to secure elements located in the corner. This setting is unacceptable.
5. Communications are connected according to the location and purpose of the pipes. As a rule, the extreme left and right are the forward and return lines of the heating system. In the center there is a gas pipe connection pipe. second left and right – hot water pipeline and cold water supply line. This arrangement is most common, but there may be other options. It is necessary to carefully study the instructions and clarify the location of the pipes of the existing model.

Connecting the boiler to the power supply system is the final step. It also possesses unique qualities. The majority of volatile boilers are very susceptible to variations in supply voltage.

Using a power stabilizer is essential for correct operation.

In the event that the boiler manufacturer has released this standard device as an extra peripheral element, connecting it will require plugging the device into the network and inserting a plug into the stabilizer output.

The connections between other types are comparable. The primary need is a connected grounding electrode; without one, the boiler electronics will continuously produce errors (failure to diagnose parasitic flame).

Following this, the installation can be deemed finished, and the subsequent start-up procedures can begin.

The diameter of the branch pipes can provide guidance when joining pipelines. It’s different on some boiler models, so there’s no chance of a mistaken communication connection.

Installation of a floor model

It is vital to guarantee adequate strength and rigidity because the installation is done on the floor. Floor units should not be installed on wooden floors; instead, a cement screed or reinforced concrete slab is necessary.

Although there isn’t a strict ban on this installation technique, we must keep in mind that wood is prone to drying out, cracking, and warping. The boiler’s stability could eventually be jeopardized, which would have highly unfavorable effects.

A floor-standing boiler ought to have its own foundation, if at all possible. This is done for large and powerful models, but you must be careful with flexible adapters because there will be a significant load on the pipes and your base’s position in relation to the general foundation may change.

Leaks or the breaking of connecting elements could come from this.

Method:

1. Unpack the boiler, check the availability of the necessary documentation. Make sure the device is complete.
2. Place the boiler on a prepared non-combustible base. Carefully align it horizontally. To do this, you need to use all the possibilities – when building the podium, ensure the horizontal support plane is as level as possible, use height-adjustable boiler supports. In extreme cases, under the legs you can put tiles of non -combustible material.
3. Connect the chimney.
4. Attach the direct and reverse pipeline of the heating system. On the side of the return side (a stream coming from the system to the boiler) it is necessary to install a filter from metal particles, scale and other small elements. This will help save the heat exchangers of the boiler and increase its service life.
5. The connection of hot and cold water pipelines is no different from connecting the heating system. A filter must also be installed on the cold water supply pipe. Some experts recommend installing cutting taps, this will help to quickly block water under pressure.
6. Connect a gas pipe through a special cutting tap. This is mandatory, there should always be a shut -off node that allows you to quickly stop the supply of fuel. You can only connect the gas pipe to the boiler yourself. Connection to the main has the right to be carried out only by a gas service specialist who has a permit and all the necessary documents. He will also check the quality of the connections using a soap solution.
7. The power connection should be made using a special socket with a grounding electrode. It is strongly recommended to use a voltage stabilizer so as not to spend money on expensive repairs to the boiler electronics.

A second, comprehensive inspection of the pipeline connection’s strength, accuracy, and dependability will be the final phase.

You can then begin configuring and launching for the first time.

How to connect a boiler

Boiler installation options vary based on the boiler’s design.

Utilizable:

• Indirect heating boiler with heat exchanger.
• Layered heating boiler.
• Electric storage boiler.

A stratified heating boiler that is external is the most affordable and easily accessible option. It is inexpensive and simple to use because it does not have a built-in heat exchanger.

Any kind of connection is established in accordance with the user’s guidelines. The procedure is very simple; all you have to do is attach the hot water collection line to the boiler’s outlet and connect the boiler’s inlet and outlet to the appropriate boiler pipes.

Hot water can be accumulated in a container using either a direct DHW outlet from the boiler or a connection to a break in the heating circuit supply line, depending on the design.

Installing a coaxial pipe step by step

Along the axis of the chimney outlet, the coaxial chimney is installed adjacent to the boiler. It is necessary to drill a hole in the outer wall that is 5–10 mm larger in diameter than the chimney’s exterior dimensions.

Either a special diamond crown or a standard hammer drill are used for this (the latter requires additional plastering and finishing work and is time-consuming).

Following that:

1. The base of the coaxial pipe is connected to the boiler chimney outlet.
2. The first chimney segment is installed. Immediately securely secured with all appropriate fasteners.
3. After it, the second section of the chimney is connected, the whole procedure is repeated. All pipe sections required by installation conditions are connected in a similar way.
4. The pipe joints and the gap between the chimney and the wall are carefully sealed.
5. The performance of the chimney is tested.

In order to allow condensation to drain into a designated container, a through hole in the wall is constructed with a small inward slope. The chimney outlet will freeze in the winter if this isn’t done.

How to start the boiler after installation

The initial launch is done in phases:

• The system is slowly filled with water. This is necessary so that all the air has time to escape. Fill until the pressure is 1-1.5 Bar.
• Check the condition of all connections, look for possible leaks.
• After this, gas is supplied and a test run of the boiler is performed. These actions are performed by technicians from the service center. They determine what adjustments need to be made to the factory settings, determine the upper and lower limits of temperature conditions, and perform other necessary actions. Independent start-up of the boiler is not recommended even for experienced people, and for night this procedure is strictly prohibited.

The best places to install a double-circuit gas boiler in a house for effective heating and hot water supply are discussed in the article "Where Should a Double-Circuit Gas Boiler be Installed + Its Connection Diagram." Knowing where things should go is crucial for convenience, effectiveness, and safety. We’ll talk about important factors like the need for structural support, the need for ventilation, and the distance from water sources. A simple connection diagram that explains how to install and connect the boiler correctly will also be supplied, guaranteeing its safe and efficient operation as part of your home’s heating system.

Useful video

You will discover where to install a double-circuit gas boiler in this video:

In which room?	Typically installed in utility rooms, such as a boiler room, basement, or garage, where there"s enough space and ventilation.
Connection Diagram	The boiler connects to the gas supply, water supply, and heating system. It usually includes pipes for water in and out, gas inlet, and outlets for heating.

Several important factors must be taken into account when deciding where in your home to install a double-circuit gas boiler in order to ensure both safety and maximum performance. The boiler must, first and foremost, be positioned in an area with adequate ventilation and air flow. This guarantees effective operation and lessens the risk of overheating.

The location should also be conveniently accessible for upkeep and repairs. In order for technicians to easily service the boiler and ultimately save time and money, accessibility is essential.

The ease of access to utility connections—particularly the water and gas supplies—is another crucial factor. The boiler will operate more efficiently and lose less energy if it is placed close to these connections, which also lowers installation costs.

Finally, when installing the boiler, it’s critical to adhere to both local building codes and the manufacturer’s instructions. In order to maintain safety standards, this includes the necessary distances between electrical components and combustible materials.

Your double-circuit gas boiler will function effectively and safely, giving your house dependable heating and hot water, if you carefully consider the installation location and adhere to these instructions.

Video on the topic

Where to install a gas boiler for heating?

🤓Competent boiler installation! Installation of a wall-mounted boiler 🔥⚡ Installation of a wall-mounted gas boiler 🐻‍❄️🐼

Installation and piping of the Conord boiler

Connecting a gas boiler to an existing heating system

Installation of a wall-mounted gas boiler. Part 2.

Connecting a double-circuit boiler and installing a heating system.

What taps are under the boiler.(European layout)